LuxtronikHeatpump Binding

This binding gives the possibility to integrate any Heatpump that is based on the Luxtronik 2 contol unit of Alpha Innotec. This includes heatpumps of:

• Alpha InnoTec
• Buderus (Logamatic HMC20, HMC20 Z)
• CTA All-In-One (Aeroplus)
• Elco
• Nibe (AP-AW10)
• Roth (ThermoAura®, ThermoTerra)
• (Siemens) Novelan (WPR NET)
• Wolf Heiztechnik (BWL/BWS)

This binding was tested with:

• Siemens Novelan LD 7

Note

If you have another heatpump the binding works with, let us know, so we can extend the list

Note: The whole functionality is based on data that was reverse engineered, so use it at your own risk.

Supported Things

This binding only supports one thing type "Luxtronik Heatpump" (heatpump).

Discovery

This binding will try to detect heat pumps that are reachable in the same IPv4 subnet.

Thing Configuration

Each heatpump requires the following configuration parameters:

parameter	required	default	description
ipAddress	yes		IP address of the heatpump
port	no	8889	Port number to connect to. This should be 8889 for most heatpumps. For heatpumps using a firmware version before V1.73 port 8888 needs to be used.
refresh	no	300	Interval (in seconds) to refresh the channel values.
showAllChannels	no	false	Show all channels (even those determined as not supported)

Channels

As the Luxtronik 2 control is able to handle multiple heat pumps with different features (like heating, hot water, cooling, solar, photovoltaics, swimming pool,...), the binding has a lot channels. Depending on the heatpump it is used with, various channels might not hold any (useful) values. If showAllChannels is not activated for the thing, this binding will automatically try to hide channels that are not available for your heat pump. As this is done using reverse engineered parameters it might not be correct in all cases. If you miss a channel that should be available for your heat pump, you can enable showAllChannels for your thing, so all channels become available. Feel free to report such a case on the forum, so we can try to improve / fix that behavior.

The following channels are holding read only values:

channel	type	advanced	description
temperatureHeatingCircuitFlow	Number:Temperature		Flow temperature heating circuit
temperatureHeatingCircuitReturn	Number:Temperature		Return temperature heating circuit
temperatureHeatingCircuitReturnTarget	Number:Temperature		Return setpoint heating circuit
temperatureBufferTankReturn	Number:Temperature	x	Return temperature in buffer tank
temperatureHotGas	Number:Temperature	x	Hot gas temperature
temperatureOutside	Number:Temperature		Outside temperature
temperatureOutsideMean	Number:Temperature		Average temperature outside over 24 h (heating limit function)
temperatureHotWater	Number:Temperature		Hot water actual temperature
temperatureHeatSourceInlet	Number:Temperature	x	Heat source inlet temperature
temperatureHeatSourceOutlet	Number:Temperature	x	Heat source outlet temperature
temperatureMixingCircuit1Flow	Number:Temperature	x	Mixing circuit 1 Flow temperature
temperatureMixingCircuit1FlowTarget	Number:Temperature	x	Mixing circuit 1 Flow target temperature
temperatureRoomStation	Number:Temperature	x	Room temperature room station 1
temperatureMixingCircuit2Flow	Number:Temperature	x	Mixing circuit 2 Flow temperature
temperatureMixingCircuit2FlowTarget	Number:Temperature	x	Mixing circuit 2 Flow target temperature
temperatureSolarCollector	Number:Temperature	x	Solar collector sensor
temperatureSolarTank	Number:Temperature	x	Solar tank sensor
temperatureExternalEnergySource	Number:Temperature	x	Sensor external energy source
inputASD	Switch	x	Input "Defrost end, brine pressure, flow rate"
inputHotWaterThermostat	Switch	x	Input "Domestic hot water thermostat"
inputUtilityLock	Switch	x	Input "EVU lock"
inputHighPressureCoolingCircuit	Switch	x	Input "High pressure cooling circuit
inputMotorProtectionOK	Switch	x	Input "Motor protection OK"
inputLowPressure	Switch	x	Input "Low pressure"
inputPEX	Switch	x	Input "Monitoring contact for potentiostat"
inputSwimmingPoolThermostat	Switch	x	Input "Swimming pool thermostat"
outputDefrostValve	Switch	x	Output "Defrost valve"
outputBUP	Switch	x	Output "Domestic hot water pump/changeover valve"
outputHeatingCirculationPump	Switch	x	Output "Heating circulation pump"
outputMixingCircuit1Open	Switch	x	Output "Mixing circuit 1 Open"
outputMixingCircuit1Closed	Switch	x	Output "Mixing circuit 1 Closed"
outputVentilation	Switch	x	Output "Ventilation"
outputVBO	Switch	x	Output "Brine pump/fan"
outputCompressor1	Switch	x	Output "Compressor 1"
outputCompressor2	Switch	x	Output "Compressor 2"
outputCirculationPump	Switch	x	Output "Circulation pump"
outputZUP	Switch	x	Output "Auxiliary circulation pump"
outputControlSignalAdditionalHeating	Switch	x	Output "Control signal additional heating"
outputFaultSignalAdditionalHeating	Switch	x	Output "Control signal additional heating/fault signal"
outputAuxiliaryHeater3	Switch	x	Output "Auxiliary heater 3"
outputMixingCircuitPump2	Switch	x	Output "Pump mixing circuit 2"
outputSolarChargePump	Switch	x	Output "Solar charge pump"
outputSwimmingPoolPump	Switch	x	Output "Swimming pool pump"
outputMixingCircuit2Closed	Switch	x	Output "Mixing circuit 2 Closed"
outputMixingCircuit2Open	Switch	x	Output "Mixing circuit 2 Open"
runtimeTotalCompressor1	Number:Time		Operation hours compressor 1
pulsesCompressor1	Number:Dimensionless		Pulses compressor 1
runtimeTotalCompressor2	Number:Time	x	Operation hours compressor 2
pulsesCompressor2	Number:Dimensionless	x	Pulses compressor 2
runtimeTotalSecondHeatGenerator1	Number:Time	x	Operation hours Second heat generator 1
runtimeTotalSecondHeatGenerator2	Number:Time	x	Operation hours Second heat generator 2
runtimeTotalSecondHeatGenerator3	Number:Time	x	Operation hours Second heat generator 3
runtimeTotalHeatPump	Number:Time		Operation hours heat pump
runtimeTotalHeating	Number:Time		Operation hours heating
runtimeTotalHotWater	Number:Time		Operation hours hot water
runtimeTotalCooling	Number:Time		Operation hours cooling
runtimeCurrentHeatPump	Number:Time	x	Heat pump running since
runtimeCurrentSecondHeatGenerator1	Number:Time	x	Second heat generator 1 running since
runtimeCurrentSecondHeatGenerator2	Number:Time	x	Second heat generator 2 running since
mainsOnDelay	Number:Time	x	Mains on delay
switchingCycleLockOff	Number:Time	x	Switching cycle lock off
switchingCycleLockOn	Number:Time	x	Switching cycle lock on
compressorIdleTime	Number:Time	x	Compressor Idle time
heatingControllerMoreTime	Number:Time	x	Heating controller More time
heatingControllerLessTime	Number:Time	x	Heating controller Less time
runtimeCurrentThermalDisinfection	Number:Time	x	Thermal disinfection running since
timeHotWaterLock	Number:Time	x	Hot water lock
bivalenceStage	Number	x	Bivalence stage
operatingStatus	Number		Operating status
errorTime0	DateTime		Timestamp error 0 in memory
errorTime1	DateTime	x	Timestamp error 1 in memory
errorTime2	DateTime	x	Timestamp error 2 in memory
errorTime3	DateTime	x	Timestamp error 3 in memory
errorTime4	DateTime	x	Timestamp error 4 in memory
errorCode0	Number		Error code Error 0 in memory
errorCode1	Number	x	Error code Error 1 in memory
errorCode2	Number	x	Error code Error 2 in memory
errorCode3	Number	x	Error code Error 3 in memory
errorCode4	Number	x	Error code Error 4 in memory
errorCountInMemory	Number	x	Number of errors in memory
shutdownReason0	Number		Reason shutdown 0 in memory
shutdownReason1	Number	x	Reason shutdown 1 in memory
shutdownReason2	Number	x	Reason shutdown 2 in memory
shutdownReason3	Number	x	Reason shutdown 3 in memory
shutdownReason4	Number	x	Reason shutdown 4 in memory
shutdownTime0	DateTime		Timestamp shutdown 0 in memory
shutdownTime1	DateTime	x	Timestamp shutdown 1 in memory
shutdownTime2	DateTime	x	Timestamp shutdown 2 in memory
shutdownTime3	DateTime	x	Timestamp shutdown 3 in memory
shutdownTime4	DateTime	x	Timestamp shutdown 4 in memory
comfortBoardInstalled	Switch	x	Comfort board installed
menuStateFull	String		Status (complete)
menuStateLine1	Number		Status line 1
menuStateLine2	Number	x	Status line 2
menuStateLine3	Number	x	Status line 3
menuStateTime	Number:Time	x	Status Time
bakeoutProgramStage	Number	x	Stage bakeout program
bakeoutProgramTemperature	Number:Temperature	x	Temperature bakeout program
bakeoutProgramTime	Number:Time	x	Runtime bakeout program
iconHotWater	Switch	x	DHW active/inactive icon
iconHeater	Number	x	Heater icon
iconMixingCircuit1	Number	x	Mixing circuit 1 icon
iconMixingCircuit2	Number	x	Mixing circuit 2 icon
shortProgramSetting	Number	x	Short program setting
statusSlave1	Number	x	Status Slave 1
statusSlave2	Number	x	Status Slave 2
statusSlave3	Number	x	Status Slave 3
statusSlave4	Number	x	Status Slave 4
statusSlave5	Number	x	Status Slave 5
currentTimestamp	DateTime	x	Current time of the heat pump
iconMixingCircuit3	Number	x	Mixing circuit 3 icon
temperatureMixingCircuit3FlowTarget	Number:Temperature	x	Mixing circuit 3 Flow set temperature
temperatureMixingCircuit3Flow	Number:Temperature	x	Mixing circuit 3 Flow temperature
outputMixingCircuit3Close	Switch	x	Output "Mixing circuit 3 Closed"
outputMixingCircuit3Open	Switch	x	Output "Mixing circuit 3 Up"
outputMixingCircuitPump3	Switch	x	Pump mixing circuit 3
timeUntilDefrost	Number:Time	x	Time until defrost
temperatureRoomStation2	Number:Temperature	x	Room temperature room station 2
temperatureRoomStation3	Number:Temperature	x	Room temperature room station 3
iconTimeSwitchSwimmingPool	Number	x	Time switch swimming pool icon
runtimeTotalSwimmingPool	Number:Time	x	Operation hours swimming pool
coolingRelease	Switch	x	Release cooling
inputAnalog	Number:ElectricPotential	x	Analog input signal
iconCirculationPump	Number	x	Circulation pumps icon
heatMeterHeating	Number:Energy		Heat meter heating
heatMeterHotWater	Number:Energy		Heat meter domestic water
heatMeterSwimmingPool	Number:Energy		Heat meter swimming pool
heatMeterTotalSinceReset	Number:Energy		Total heat meter
heatMeterFlowRate	Number:VolumetricFlowRate		Heat meter flow rate
outputAnalog1	Number:ElectricPotential	x	Analog output 1
outputAnalog2	Number:ElectricPotential	x	Analog output 2
timeLockSecondHotGasCompressor	Number:Time	x	Lock second compressor hot gas
temperatureSupplyAir	Number:Temperature	x	Supply air temperature
temperatureExhaustAir	Number:Temperature	x	Exhaust air temperature
runtimeTotalSolar	Number:Time	x	Operating hours solar
outputAnalog3	Number:ElectricPotential	x	Analog output 3
outputAnalog4	Number:ElectricPotential	x	Analog output 4
outputSupplyAirFan	Number:ElectricPotential	x	Supply air fan (defrost function)
outputExhaustFan	Number:ElectricPotential	x	Exhaust fan
outputVSK	Switch	x	Output VSK
outputFRH	Switch	x	Output FRH
inputAnalog2	Number:ElectricPotential	x	Analog input 2
inputAnalog3	Number:ElectricPotential	x	Analog input 3
inputSAX	Switch	x	Input SAX
inputSPL	Switch	x	Input SPL
ventilationBoardInstalled	Switch	x	Ventilation board installed
flowRateHeatSource	Number:VolumetricFlowRate	x	Flow rate heat source
linBusInstalled	Switch	x	LIN BUS installed
temperatureSuctionEvaporator	Number:Temperature	x	Temperature suction evaporator
temperatureSuctionCompressor	Number:Temperature	x	Temperature suction compressor
temperatureCompressorHeating	Number:Temperature	x	Temperature compressor heating
temperatureOverheating	Number:Temperature	x	Overheating
temperatureOverheatingTarget	Number:Temperature	x	Overheating target
highPressure	Number:Pressure	x	High pressure
lowPressure	Number:Pressure	x	Low pressure
outputCompressorHeating	Switch	x	Output compressor heating
controlSignalCirculatingPump	Number:Energy	x	Control signal circulating pump
fanSpeed	Number	x	Fan speed
temperatureSafetyLimitFloorHeating	Switch	x	Safety temperature limiter floor heating
powerTargetValue	Number:Energy	x	Power target value
powerActualValue	Number:Energy	x	Power actual value
temperatureFlowTarget	Number:Temperature	x	Temperature flow set point
operatingStatusSECBoard	Number	x	SEC Board operating status
fourWayValve	Number	x	Four-way valve
compressorSpeed	Number	x	Compressor speed
temperatureCompressorEVI	Number:Temperature	x	Compressor temperature EVI (Enhanced Vapour Injection)
temperatureIntakeEVI	Number:Temperature	x	Intake temperature EVI
temperatureOverheatingEVI	Number:Temperature	x	Overheating EVI
temperatureOverheatingTargetEVI	Number:Temperature	x	Overheating EVI target
temperatureCondensation	Number:Temperature	x	Condensation temperature
temperatureLiquidEEV	Number:Temperature	x	Liquid temperature EEV (electronic expansion valve)
temperatureHypothermiaEEV	Number:Temperature	x	Hypothermia EEV
pressureEVI	Number:Pressure	x	Pressure EVI
voltageInverter	Number:ElectricPotential	x	Voltage inverter
temperatureHotGas2	Number:Temperature	x	Hot gas temperature sensor 2
temperatureHeatSourceInlet2	Number:Temperature	x	Temperature sensor heat source inlet 2
temperatureIntakeEvaporator2	Number:Temperature	x	Intake temperature evaporator 2
temperatureIntakeCompressor2	Number:Temperature	x	Intake temperature compressor 2
temperatureCompressor2Heating	Number:Temperature	x	Temperature compressor 2 heating
temperatureOverheating2	Number:Temperature	x	Overheating 2
temperatureOverheatingTarget2	Number:Temperature	x	Overheating target 2
highPressure2	Number:Pressure	x	High pressure 2
lowPressure2	Number:Pressure	x	Low pressure 2
inputSwitchHighPressure2	Switch	x	Input pressure switch high pressure 2
outputDefrostValve2	Switch	x	Output defrost valve 2
outputVBO2	Switch	x	Output brine pump/fan 2
outputCompressor1_2	Switch	x	Compressor output 1 / 2
outputCompressorHeating2	Switch	x	Compressor output heating 2
secondShutdownReason0	Number	x	Reason shutdown 0 in memory
secondShutdownReason1	Number	x	Reason shutdown 1 in memory
secondShutdownReason2	Number	x	Reason shutdown 2 in memory
secondShutdownReason3	Number	x	Reason shutdown 3 in memory
secondShutdownReason4	Number	x	Reason shutdown 4 in memory
secondShutdownTime0	DateTime	x	Timestamp shutdown 0 in memory
secondShutdownTime1	DateTime	x	Timestamp shutdown 1 in memory
secondShutdownTime2	DateTime	x	Timestamp shutdown 2 in memory
secondShutdownTime3	DateTime	x	Timestamp shutdown 3 in memory
secondShutdownTime4	DateTime	x	Timestamp shutdown 4 in memory
temperatureRoom	Number:Temperature	x	Room temperature actual value
temperatureRoomTarget	Number:Temperature	x	Room temperature set point
temperatureHotWaterTop	Number:Temperature	x	Temperature domestic water top
frequencyCompressor	Number:Frequency	x	Compressor frequency
channel232	Number	x	Channel 232
channel233	Number	x	Channel 233
channel234	Number	x	Channel 234
channel235	Number	x	Channel 235
frequencyCompressorTarget	Number:Frequency	x	Compressor Target Frequency
channel237	Number	x	Channel 237
channel238	Number	x	Channel 238
channel239	Number	x	Channel 239
channel240	Number	x	Channel 240
channel241	Number	x	Channel 241
channel242	Number	x	Channel 242
channel243	Number	x	Channel 243
channel244	Number	x	Channel 244
channel245	Number	x	Channel 245
channel246	Number	x	Channel 246
channel247	Number	x	Channel 247
channel248	Number	x	Channel 248
channel249	Number	x	Channel 249
channel250	Number	x	Channel 250
channel251	Number	x	Channel 251
channel252	Number	x	Channel 252
channel253	Number	x	Channel 253
flowRateHeatSource2	Number:VolumetricFlowRate	x	Flow Rate Heat Source
channel255	Number	x	Channel 255
channel256	Number	x	Channel 256
heatingPowerActualValue	Number:Power	x	Heating Power Actual Value
channel258	Number	x	Channel 258
channel259	Number	x	Channel 259
channel260	Number	x	Channel 260

The usage of the numbered channels above is currently unknown. If you are able to directly match one of the values to any value reported by your heat pump, feel free to report back on the forum, so we are able to give the channel a proper name instead.

The following channels are also writable:

channel	type	advanced	description
temperatureHeatingParallelShift	Number:Temperature		Heating temperature (parallel shift)
temperatureHotWaterTarget	Number:Temperature		Hot water target temperature
heatingMode	Number		Heating mode
hotWaterMode	Number		Hot water operating mode
thermalDisinfectionMonday	Switch	x	Thermal disinfection (Monday)
thermalDisinfectionTuesday	Switch	x	Thermal disinfection (Tuesday)
thermalDisinfectionWednesday	Switch	x	Thermal disinfection (Wednesday)
thermalDisinfectionThursday	Switch	x	Thermal disinfection (Thursday)
thermalDisinfectionFriday	Switch	x	Thermal disinfection (Friday)
thermalDisinfectionSaturday	Switch	x	Thermal disinfection (Saturday)
thermalDisinfectionSunday	Switch	x	Thermal disinfection (Sunday)
thermalDisinfectionPermanent	Switch	x	Thermal disinfection (Permanent)
comfortCoolingMode	Number		Comfort cooling mode
temperatureComfortCoolingATRelease	Number:Temperature		Comfort cooling AT release
temperatureComfortCoolingATReleaseTarget	Number:Temperature		Comfort cooling AT release target
temperatureHeatingLimit	Number:Temperature		Temperature Heating Limit
comfortCoolingATExcess	Number:Time		AT Excess
comfortCoolingATUndercut	Number:Time		AT undercut

Example

Below you can find some example textual configuration for a heatpump with some basic functionallity. This can be extended/adjusted according to your needs and depending on the availability of channels (see list above).

heatpump.things:

Thing luxtronikheatpump:heatpump:heatpump "Heatpump" [
    ipAddress="192.168.178.12",
    port="8889",
    refresh="300"
]

heatpump.items:

Group    gHeatpump   "Heatpump"   <temperature>

Number:Temperature HeatPump_Temp_Outside   "Temperature outside [%.1f °C]"   <temperature> (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:temperatureOutside" }
Number:Temperature HeatPump_Temp_Outside_Avg     "Avg. temperature outside [%.1f °C]"  <temperature> (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:temperatureOutsideMean" }

Number:Time HeatPump_Hours_Heatpump  "Operating hours [%d h]"  <clock> (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:runtimeTotalHeatPump" }
Number:Time HeatPump_Hours_Heating   "Operating hours heating [%d h]"  <clock> (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:runtimeTotalHeating" }
Number:Time HeatPump_Hours_Warmwater "Operating hours hot water [%d h]" <clock> (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:runtimeTotalHotWater" }

String HeatPump_State_Ext   "State [%s]"   (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:menuStateFull" }

Number HeatPump_heating_operation_mode   "Heating operation mode [%s]"  (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:heatingMode" }
Number HeatPump_heating_temperature   "Heating temperature [%.1f]"  (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:temperatureHeatingParallelShift" }
Number HeatPump_warmwater_operation_mode   "Hot water operation mode [%s]"  (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:hotWaterMode" }
Number HeatPump_warmwater_temperature   "Hot water temperature [%.1f]"  (gHeatpump) { channel="luxtronikheatpump:heatpump:heatpump:temperatureHotWaterTarget" }

heatpump.sitemap:

sitemap heatpump label="Heatpump" {
    Frame label="Heatpump" {
        Text item=HeatPump_State_Ext
        Text item=HeatPump_Temperature_1
        Text item=HeatPump_Outside_Avg
        Text item=HeatPump_Hours_Heatpump
        Text item=HeatPump_Hours_Heating
        Text item=HeatPump_Hours_Warmwater
        Switch item=HeatPump_heating_operation_mode  mappings=[0="Auto", 1="Auxiliary heater", 2="Party", 3="Holiday", 4="Off"]
        Setpoint item=HeatPump_heating_temperature minValue=-10 maxValue=10 step=0.5
        Switch item=HeatPump_warmwater_operation_mode  mappings=[0="Auto", 1="Auxiliary heater", 2="Party", 3="Holiday", 4="Off"]
        Setpoint item=HeatPump_warmwater_temperature minValue=10 maxValue=65 step=1
    }
}

Development Notes

This binding was initially based on the Novelan/Luxtronik Heat Pump Binding (opens new window) for openHAB 1.

Luxtronik control units have an internal webserver which serves a Java applet. This applet can be used to configure some parts of the heat pump. The applet itselves uses a socket connection to fetch and send data to the heatpump. This socket is also used by this binding. To get some more information on how this socket works you can check out other Luxtronik tools like Luxtronik2 for NodeJS (opens new window).

A detailed parameter descriptions for the Java Webinterface can be found in the Loxwiki (opens new window)

Caught a mistake or want to contribute to the documentation? Edit this page on GitHub (opens new window)